Atomic’s Hawx Prime 105 is made for comfortable high-performance skiing. A 100mm last and a well-considered shape hold the foot without squeezing, whilst still providing the control needed for good skiing. The pre-shaped 3D Gold liner adds precision and improves the fit, as well as having Thinsulate to wrap the whole foot for warmth and comfort. The shell benefits from Prolite design that blends lightness, power and sensitivity, as well as the customised fitting of the mouldable Memory Fit technology.Ability LevelOverviewFitMedium fit around the heel and ankle, medium to high instep, medum to wide across the forefoot.Shell PU Memory Fit shell and cuff, mouldable. The advanced heat fitting technology of Memory Fit creates a fully personalised shell and cuff in minutes. The key is Memolink, a special additive that improves the mouldability and stretch characteristics of the plastic. The boot shell is heated in an oven, then the skier’s foot is placed inside the complete boot whilst it cools. With the foot’s natural standing pressure, the forefoot of the boot can expand up to 3mm per side and the ankle area up to 5mm per side.Liner3D Gold W Thinsulate, mouldable. Thermoformable material is used in the heel, ankle and midfoot areas. The liner is heated in an oven and is cooled to form to the shape of the skier’s feet. 3D means pre-shaped heel and ankles areas for better foot hold and comfort. Thinsulate is the world’s best-known insulation and its use keeps feet warmer.Key FeaturesProliteProlite is a way of building skis and boots that turns traditional thinking on its head. Instead of starting with a standard construction and cutting material away to save weight, Prolite does the opposite. It starts with the slimmest possible profile and then it builds up reinforcements in key areas where strength is needed.Power ShiftPower Shift allows the forward lean to be adjusted to 13o, 15o or 17o simply by moving the power control up and down. You can also alter the flex index by +/- 10 flex points by adding or removing a screw. Creates a completely personalised set-up.energy BackboneThe energy Backbone is a reinforced, asymmetric backbone that provides extra strength for powerful skiing plus enhanced lateral energy transmission for better edge grip.ThinsulateThe more air a material traps in a given space the greater its insulating value. The microfibres in 3M Thinsulate insulation are far finer than any other fibres, which means they trap more insulating air in less space, even when wet. This keeps feet warm and responsive even in extremely cold and damp conditions.SpecificationCategory: AlpineFlex: 105Last Width: 100-106Custom Shell: YesCustom Liner: YesPower Strap: 40mmVolume: MediumClips: n/aSole Unit: Alpine (Adult ISO 5355)Pin Inserts: NoHike Mode: NoWeight (g): 1625Binding Compatibility: Alpine, Grip Walk, Walk To Ride, Multi Norm [Full Details]
The RC4 The Curv One 110 will appeal to good intermediate and advanced skiers who are looking for a higher volume boot that doesn't sacrifice performance or hold back on custom fitting options. It uses Fischer's unique Vacuum moulding process that forms the shell to the skier's foot during the initial boot fit. This reduces pressure points and improves the foot hold at the same time; the comfort is enhanced further by the customisation of the heat moulded liner. It's also impressively light, thanks to clever engineering that alters the thickness of shell: making it thin where it needs to wrap, thicker where it supports.Ability LevelOverviewFitAverage around the heel and ankle with a slightly more generous feel on the forefoot and average instep height.Shell Vacuum HV shell, customisable.LinerRC4 The Curv One 110, customisable.Key FeaturesSomatecIn their natural, relaxed position, your feet form a V-shape. In this stance the knees remain parallel when flexed. Fischer took these anatomical facts into account when developing Soma-Tec. The feet remain relaxed in their natural V-position, so knee and ankle joints no longer have to be twisted inward and less strain is placed on the joints. At the same time, edge changes are made easier and energy is transmitted to the ski more accurately.VACUUMVacuum technology uses a unique process and a specially developed high-tech plastic to adapt the shell of the ski boot to the anatomy of any foot. Prior to fitting the plastic of the boots are heated and softened. With the liner inserted, the skier’s foot is placed inside. A special cooling pad is placed around the outside, followed by a compression bag linked to the Vacuum Fit station. The skier then stands on the station in a pre-determined position, this will ensure the boot cools down and shapes to the skier’s natural stance. Once in position, air is pumped into the compression bags, pushing them against the boot and improving the mould being taken of the foot. This procedure achieves a sporty, comfortable fit that is unrivalled in this segment. The heel and ankle area can be expanded or compressed to create best possible shape; the forefoot can be made roomier. Vacu-PlastThis unique material was developed exclusively for use with Fischer ski boots. Apart from its extraordinary moulding properties Vacu-Plast also has other special features: it is very temperature stable, meaning it isn’t adversely affected on extreme cold days when certain plastics become very stiff; it is lighter than other materials used on performance ski boots, and it has better vibration dampening.SpecificationCategory: AlpineFlex: 110Last Width: 101 (+/- 3mm)Custom Shell: YesCustom Liner: YesPower Strap: Velcro 35mmVolume: Medium-HighClips: 4 x GT Aluminium, MicroadjustableSole Unit: Grip Walk (ISO 9523)Pin Inserts: NoHike Mode: NoWeight (g): 1980 (1/2 pair size 26.5)Binding Compatibility: GripWalk, Multi Norm [Full Details]
The Atomic Redster CS 70 LC is perfect for the lighter or younger skier looking for a race fit and feel but in a more forgiving and easier to flex model. The Redster range has years of Atomic racing knowhow behind it, which carries down into the softer and junior models too. They have used the 96mm Narrow Last to provide the closeness of fit and performance that good skiers want and a Progressive Race Shell that uses a thicker but softer plastic to give a superior damp quality to the way the boot flexes. Memory Fit technology means the clog, cuff and Liner can be moulded in-store to help tune the fit even further, in minutes. A low cuff design means that the top of the boot isn't too close to the knee, which can cause problems flexing with shorter leg lengths. This is a great choice for aspiring young racers or good but lightweight shorter adults. Ability LevelBoots12OverviewFitLow volume close fit. Snug heel pocket and narrow across the forefoot. ShellMemory Fit, mouldable. The advanced heat fitting technology of Memory Fit creates a fully personalised shell and cuff in minutes. The key is Memolink, a special additive that improves the mouldability and stretch characteristics of the plastic. The boot shell is heated in an oven, then the skier's foot is placed inside the complete boot whilst it cools. With the foot's natural standing pressure, the forefoot of the boot can expand up to 3mm per side and the ankle area up to 5mm per side.LinerSliver. Mouldable around the ankle area and uses a 3D Stretch Toe Box.Key FeaturesProgressive Race Shell A thicker but softer plastic provides better dampening properties and a more supple feel for conditions Memory Fit A full mouldable shell for an optimal fit and foot to boot connectivity General InformationCategory: RaceFlex: 70Last Width: 96Custom Shell: NoCustom Liner: YesPower Strap: Velcro 35mmVolume: LowClips: 4 x 7000-Series Aluminium, MicroadjustableSole Unit: Alpine (ISO 5355)Pin Inserts: NoSizing Hike Mode: NoRange of Motion: n/aWeight (g): 2017 (1/2 pair size 24.5)Binding Compatibility: Alpine, GripWalk, WTR, Multi Norm [Full Details]
The Speedmachine 3 85 W packs gentle punch compared to its stiffer counterparts, but it keeps the key features and medium volume fit that make the Speedmachine 3 range stand out. The new 3Force construction uses an innovative stiff honeycomb subframe to provide power and control whilst staying light, and a softer plastic around key fit areas to comfortably wrap the feet with an even softer plastic over the instep to take the hassle out of getting them on or off. It too can be fine-tuned with Infrared technology and Adjustable Calf Profile meaning the shell can be quickly customised to really dial in the fit. The 3D Performance Fit Primaloft liner is pre-shaped and provides the perfect interface between the shell and foot which can heat moulded to give just the right level support and comfort you need. The addition of Primaloft keeps feet warm to make sure you spend more time on the hill skiing for longer, happy feet equals happy skiers. Ability LevelOverviewFitMedium ankle pocket provides good heel hold, a medium to wide forefoot and and average to high instep. Round toe shape.Shell Infrared PU shell and cuff, mouldable. Speedmachine shells offer a relaxed fit with easy entry and exit, but plenty of foot hold for performance skiing. The Infrared Technology is a super-effective way to customise the fit precisely for the best possible shape.Liner3D Performance Fit PrimaLoft, mouldable. The 3D pre-shaping mimics the natural shape of ankle bones, improving both the comfort and the heel hold by evening out the pressure. PrimaLoft ensures extra comfort and warmth.Key Features3Force Technology3 densities of plastic combine to create the perfect balance of performance, fit and lightness. The secret lies in the new rigid plastic material, which provides a powerful frame and has been given an innovative geometry. Its Honeycomb construction lightens the overall weight of the boot, but increases the surface area to integrate perfectly with the softer compounds. Softer plastics are used to complete the shell for comfort and overall lightness.Infrared TechnologyInfrared Technology is a super-effective way to customise the fit precisely for the best possible shape. The shell is slowly heated and then a vacuum system is used to gently reshape the plastic where any additional moulding is need to get the best match to a skier's feet.PrimaLoftPrimaLoft is an industry-leading waterproof, synthetic insulation. It provides warmth and comfort so you can focus on enjoying the conditions.SpecificationCategory: AlpineFlex: 85Last Width: 100Custom Shell: YesCustom Liner: YesPower Strap: Velcro 35mmVolume: Medium Clips: 4 x Aluminium, MicroadjustableSole Unit: Grip Walk (ISO 9523)Pin Inserts: NoHike Mode: NoWeight (g): Grip Walk, WTR, Multi NormBinding Compatibility: Yes [Full Details]
The new Cosmos Tour takes everything that was great about the Cosmos III and builds on it. It’s the perfect option for ski tourers with high volume feet who have previously struggled to get comfortable AT boots. The new Cabrio Hybrid construction ensures easy mobility of the cuff for climbing and gives the skier solid support during turn. Grilamid construction is lightweight for the way up but provides plenty of power on the way down. Powerlite 2.0 technology means an impressive 60 degrees of articulation. A simple yet effective Rear Hook ski/walk mechanism requires minimal effort yet is strong and dependable. The mouldable PWR Lite High liner improves the fit and comfort; full length Vibram soles increase grip. 3 ergal Micro-Adjustable Buckles and a cable closure over the forefoot make tightening or loosening the boots simple.Ability LevelTour2OverviewFitAverage rear foot volume with a higher volume forefoot and generous over the instep.ShellGrilamid Powerlite shell and cuff. Powerlite 2.0 boots are built from Grilamid, making them stiffer, lighter, and thinner than other lightweight shells. The result is precise, solid and secure skiing with instant comfort. 3 piece or cabrio design uses a shell, cuff and separate tongue for improved range of motion, comfort and ease of entry/exit.LinerPWR Lite High, mouldable. Lightweight, warm and custom moulded for the best possible fit.Key FeaturesRear Hook Ski/Walk Mechanismeasy to operate, the Powerlite 2.0 rear hook mechanism combines strength and stability in ski mode with total freedom when skinning or walking. This next generation hook mechanism locks automatically when downhill skiing. Full-Length Vibram Bi-Density RubberFull-length Vibram bi-density rubber under the instep area provides maximum grip when scrambling over any terrain that isn't snow. The bi-density composition has firmer black rubber around the sole's perimeter to provide durability and superior edging power in step-in bindings. Softer red rubber in the sole's midsection gives maximum grip for scrambling.Lock CatchesScott's Locking Buckle Catches keep the buckle bails in place when the buckles are opened for hiking.Adjustable SpoilerAn Asymmetric Spoiler provides medial and rearward support.Dual Action TongueThe newly developed Dual Action Tongue allows an easy step in and out of the boot. Due to the flexibility of the tongue it follows the movement when in walk mode and is fully linked to the cuff when skiing, which results in a more progressive flex. General InformationCategory: BackcountryFlex: 120Last Width: 103.5Custom Shell: NoCustom Liner: YesPower Strap: VelcroVolume: HighClips: 3 x ergal® Microadjustable Buckles + Cable closureSole Unit: Tour (ISO 9523)Pin Inserts: YesSizing Hike Mode: YesRange of Motion: 60Weight (g): 1390 (1/2 pair size 26.5)Binding Compatibility: Multi Norm, PinCert, Pin [Full Details]
The new Cosmos Tour takes everything that was great about the Cosmos III and builds on it. It’s the perfect option for ski tourers with high volume feet who have previously struggled to get comfortable AT boots. The new Cabrio Hybrid construction ensures easy mobility of the cuff for climbing and gives the skier solid support during turn. Grilamid construction is lightweight for the way up but provides plenty of power on the way down. Powerlite 2.0 technology means an impressive 60 degrees of articulation. A simple yet effective Rear Hook ski/walk mechanism requires minimal effort yet is strong and dependable. The mouldable PWR Lite High liner improves the fit and comfort; full length Vibram soles increase grip. 3 ergal Micro-Adjustable Buckles and a cable closure over the forefoot make tightening or loosening the boots simple.Ability LevelTour2OverviewFitAverage rear foot volume with a higher volume forefoot and generous over the instep.ShellGrilamid Powerlite shell and cuff. Powerlite 2.0 boots are built from Grilamid, making them stiffer, lighter, and thinner than other lightweight shells. The result is precise, solid and secure skiing with instant comfort. 3 piece or cabrio design uses a shell, cuff and separate tongue for improved range of motion, comfort and ease of entry/exit.LinerPWR Lite High, mouldable. Lightweight, warm and custom moulded for the best possible fit.Key FeaturesRear Hook Ski/Walk Mechanismeasy to operate, the Powerlite 2.0 rear hook mechanism combines strength and stability in ski mode with total freedom when skinning or walking. This next generation hook mechanism locks automatically when downhill skiing. Full-Length Vibram Bi-Density RubberFull-length Vibram bi-density rubber under the instep area provides maximum grip when scrambling over any terrain that isn't snow. The bi-density composition has firmer black rubber around the sole's perimeter to provide durability and superior edging power in step-in bindings. Softer red rubber in the sole's midsection gives maximum grip for scrambling.Lock CatchesScott's Locking Buckle Catches keep the buckle bails in place when the buckles are opened for hiking.Adjustable SpoilerAn Asymmetric Spoiler provides medial and rearward support.Dual Action TongueThe newly developed Dual Action Tongue allows an easy step in and out of the boot. Due to the flexibility of the tongue it follows the movement when in walk mode and is fully linked to the cuff when skiing, which results in a more progressive flex. General InformationCategory: BackcountryFlex: 120Last Width: 103.5Custom Shell: NoCustom Liner: YesPower Strap: VelcroVolume: HighClips: 3 x ergal® Microadjustable Buckles + Cable closureSole Unit: Tour (ISO 9523)Pin Inserts: YesSizing Hike Mode: YesRange of Motion: 60Weight (g): 1390 (1/2 pair size 26.5)Binding Compatibility: Multi Norm, PinCert, Pin [Full Details]
The new Cosmos Tour takes everything that was great about the Cosmos III and builds on it. It’s the perfect option for ski tourers with high volume feet who have previously struggled to get comfortable AT boots. The new Cabrio Hybrid construction ensures easy mobility of the cuff for climbing and gives the skier solid support during turn. Grilamid construction is lightweight for the way up but provides plenty of power on the way down. Powerlite 2.0 technology means an impressive 60 degrees of articulation. A simple yet effective Rear Hook ski/walk mechanism requires minimal effort yet is strong and dependable. The mouldable PWR Lite High liner improves the fit and comfort; full length Vibram soles increase grip. 3 ergal Micro-Adjustable Buckles and a cable closure over the forefoot make tightening or loosening the boots simple.Ability LevelTour2OverviewFitAverage rear foot volume with a higher volume forefoot and generous over the instep.ShellGrilamid Powerlite shell and cuff. Powerlite 2.0 boots are built from Grilamid, making them stiffer, lighter, and thinner than other lightweight shells. The result is precise, solid and secure skiing with instant comfort. 3 piece or cabrio design uses a shell, cuff and separate tongue for improved range of motion, comfort and ease of entry/exit.LinerPWR Lite High, mouldable. Lightweight, warm and custom moulded for the best possible fit.Key FeaturesRear Hook Ski/Walk Mechanismeasy to operate, the Powerlite 2.0 rear hook mechanism combines strength and stability in ski mode with total freedom when skinning or walking. This next generation hook mechanism locks automatically when downhill skiing. Full-Length Vibram Bi-Density RubberFull-length Vibram bi-density rubber under the instep area provides maximum grip when scrambling over any terrain that isn't snow. The bi-density composition has firmer black rubber around the sole's perimeter to provide durability and superior edging power in step-in bindings. Softer red rubber in the sole's midsection gives maximum grip for scrambling.Lock CatchesScott's Locking Buckle Catches keep the buckle bails in place when the buckles are opened for hiking.Adjustable SpoilerAn Asymmetric Spoiler provides medial and rearward support.Dual Action TongueThe newly developed Dual Action Tongue allows an easy step in and out of the boot. Due to the flexibility of the tongue it follows the movement when in walk mode and is fully linked to the cuff when skiing, which results in a more progressive flex. General InformationCategory: BackcountryFlex: 120Last Width: 103.5Custom Shell: NoCustom Liner: YesPower Strap: VelcroVolume: HighClips: 3 x ergal® Microadjustable Buckles + Cable closureSole Unit: Tour (ISO 9523)Pin Inserts: YesSizing Hike Mode: YesRange of Motion: 60Weight (g): 1390 (1/2 pair size 26.5)Binding Compatibility: Multi Norm, PinCert, Pin [Full Details]
The new Cosmos Tour takes everything that was great about the Cosmos III and builds on it. It’s the perfect option for ski tourers with high volume feet who have previously struggled to get comfortable AT boots. The new Cabrio Hybrid construction ensures easy mobility of the cuff for climbing and gives the skier solid support during turn. Grilamid construction is lightweight for the way up but provides plenty of power on the way down. Powerlite 2.0 technology means an impressive 60 degrees of articulation. A simple yet effective Rear Hook ski/walk mechanism requires minimal effort yet is strong and dependable. The mouldable PWR Lite High liner improves the fit and comfort; full length Vibram soles increase grip. 3 ergal Micro-Adjustable Buckles and a cable closure over the forefoot make tightening or loosening the boots simple.Ability LevelTour2OverviewFitAverage rear foot volume with a higher volume forefoot and generous over the instep.ShellGrilamid Powerlite shell and cuff. Powerlite 2.0 boots are built from Grilamid, making them stiffer, lighter, and thinner than other lightweight shells. The result is precise, solid and secure skiing with instant comfort. 3 piece or cabrio design uses a shell, cuff and separate tongue for improved range of motion, comfort and ease of entry/exit.LinerPWR Lite High, mouldable. Lightweight, warm and custom moulded for the best possible fit.Key FeaturesRear Hook Ski/Walk Mechanismeasy to operate, the Powerlite 2.0 rear hook mechanism combines strength and stability in ski mode with total freedom when skinning or walking. This next generation hook mechanism locks automatically when downhill skiing. Full-Length Vibram Bi-Density RubberFull-length Vibram bi-density rubber under the instep area provides maximum grip when scrambling over any terrain that isn't snow. The bi-density composition has firmer black rubber around the sole's perimeter to provide durability and superior edging power in step-in bindings. Softer red rubber in the sole's midsection gives maximum grip for scrambling.Lock CatchesScott's Locking Buckle Catches keep the buckle bails in place when the buckles are opened for hiking.Adjustable SpoilerAn Asymmetric Spoiler provides medial and rearward support.Dual Action TongueThe newly developed Dual Action Tongue allows an easy step in and out of the boot. Due to the flexibility of the tongue it follows the movement when in walk mode and is fully linked to the cuff when skiing, which results in a more progressive flex. General InformationCategory: BackcountryFlex: 120Last Width: 103.5Custom Shell: NoCustom Liner: YesPower Strap: VelcroVolume: HighClips: 3 x ergal® Microadjustable Buckles + Cable closureSole Unit: Tour (ISO 9523)Pin Inserts: YesSizing Hike Mode: YesRange of Motion: 60Weight (g): 1390 (1/2 pair size 26.5)Binding Compatibility: Multi Norm, PinCert, Pin [Full Details]